Setting up wi-fi on huawei HG532e, as well as in router mode

Recently, the question of how to set up wifi on a huawei byfly modem has become very popular. This modem is issued with services, its full model is Huawei Gateway HG532e. Therefore, they often ask how to set up huawei hg532e in router mode, and then wi-fi on it . The modem is remarkable in that it is very convenient, unpretentious and relatively easy to configure.

ATTENTION! We highly recommend an article about the overheating of your laptop that has begun. Users often forget about this. It is from overheating that expensive laptop parts burn out. The issue of overheating is solved simply, you just have to not put it off until later.

Introduction

It may take 10 to 20 minutes to set up this modem, and sometimes more, depending on experience and ability to use such equipment.

Let's get to the settings

In order to start setting up the settings for the huawei hg532e byfly modem, you need to go to some browser, such as the Internet browser Opera or Mozilla Firefox or another.

Usually, before you start configuring the modem, you must reset all previous changes made to it and return it to initial settings. To reset the settings, you need to press and hold for about 10 seconds the pressed reset button, which is located almost at the power wire, with something sharp.

And so, in order to deal with the issue of huawei hg532e router, let's get down to the settings. In the browser, in the field in which we usually enter the name of the sites, enter the path to the modem settings - 192.168.1.1 (do not hesitate when entering in the address bar, just imagine that you are entering the site address).

In the Username and Password lines that appear, you need to enter the word admin - both in the first and second lines.

After entering, a window will appear.

We go to the line Basic.

We click with the mouse on Internet_B_0_33.

The following window appears.

We make the following changes - change Connection Type: bridge to Connection Type: PPPoE.

An additional menu will appear.

In the additional menu that appears, you need to register Username and Password, those that are written in the contract with ByFly. It contains a personal username and password. Make sure that the entered characters are correct, if at least one mistake sneaks here, then there will be no access to the Internet.

Eventually…

To apply the settings, click the lowest button - Submit. After applying the settings, after about 20 seconds, the Internet should start working. To check, we register any site in the browser.

Everything, with these settings made to the modem, the huawei hg532e router was configured, that is, we connected the computer to the Internet using network cable in router mode.

Also, do not forget to immediately install an antivirus with the advent of access to the Internet, an article about anti-virus protection of a computer will help you with this. Also, you can always contact us and our master will perform this setting quickly and efficiently.

Setting up Wi-Fi on huawei hg532e

Now let's deal with the issue of setting up wifi huawei hg532e, that is, setting up a wireless wifi connection on byfly.
In the Basic tab, move to the Wlan subsection.

We change almost nothing, only in the SSID: - enter the name of the future WiFi networks, SSID, check the SSID:Enable checkbox and make up a password for the almost already created Wi-Fi connection in the corresponding line: WPA pre-shared key.

We apply the changes made with the Submit button and everything is ready. ByFly wireless network on Huawei modem Home Gateway HG532e has been created.

Checking the created Wi-Fi network

Now you can try out a wireless wi-fi network, you need to go to the Network and Control Center on your computer and public access(located Start - Control Panel - Network and Internet - Network and Sharing Center).

We find there the name of the created wireless network, try to connect, a field should appear asking you to enter the password that you entered in the WPA pre-shared key line. Here's how to set up wifi byfly huawei hg532e.

And so on any device that supports Wi-Fi, you must first find the name of your Wi-Fi connection, and then enter the password. Here is how to set up huawei hg532e byfly setup.

If all the settings are entered correctly, usually there should be no problems, but it is not a fact that there will be no additional nuances during the setup. If it was not possible to produce it, then you can contact us at, our masters will solve the issue of setting up wifi on byfly huawei, inexpensively and as soon as possible.

• I like it
• I did not like

• August 25, 2013
• Alex site

Modems M200A and M200B differ only in support of Anex A or Anex B. If you have a burglar alarm at home, then the M200B modem is most likely installed.

Top view of the latest modification of the modem:

Back view:

Setting up a network card

So let's get started Wi-Fi setup on the modem. We connect the 1-3 port of the modem and the network card of the computer with the patch cord that comes with the kit. Then we run the ping 192.168.1.1 –t command

If the DHCP server is enabled on the modem, and the IP address on the network card is automatic, you should see the following picture:

If the message " The specified node is not available"you will have to check if the IP address is automatic on your network adapter. To do this, click on the computer icon in the tray, select " Network and Sharing Center":

Choose " Change adapter settings" in the window that opens:

Do a right-click on the " Connection via local network " and choose " Properties":

In properties Internet Protocol Version 4 (TCP/IPv4) change the tabs to " Obtain an IP address automatically", "Obtain DNS server address automatically":

If even after these manipulations with the ping 192.168.1.1 –t command, response packets do not begin to arrive, you need to reset the modem with a reset or. On old ZTE modems, this can lead to the loss of all provider settings! You will have to tune it exactly according to the instructions if you are not confident in your abilities.set up a better static address. For those who like to take risks, the Reset button is usually hidden on the "sole" of the modem in order to avoid accidental pressing, plus it is recessed into the case, and in order to press it, you need to use some thin object (for example, a ballpoint pen refill). ):

These actions must be done if you forgot the password from the modem's admin panel or want to return the modem's settings to default.

Setting up PPPoE on the modem

After the ping 192.168.1.1 -t command finally starts running, open your favorite Internet browser and write in the input line: http://192.168.1.1 . The default password and login in this modem is admin. Press the button " Send":

Let's start modem setup. Go to tab ""Put a tabISP on PPPoA/PPPoE. We write down the login and password specified in the contract in the fieldsusername And password. Tabulator default routeput in positionYes, we leave everything else as it is:

Setting WiFi hotspots access

Set up Wi-Fi on the modem. Go to tab " Wireless" put the access point in the fastest mode " 802.11g+n" with channel width 20/40Mhz which will give you the best performance.

Be sure to activate PerSSID Switch. If you want a wireless network KardaNet was not visible to the neighbors set " no" against Broadcast SSID. If you want the network to be discovered by the WINDOWS Wi-Fi adapter configuration utility, put on the tab " Yes". Well, of course, so that the neighbors cannot use your Internet, we set up encryption by inventing for the field pre-shared key a key of at least eight arbitrary characters. Choose the strongest encryption type - WPA2-PSK, encryption algorithm AES. All fairly new devices support this wireless configuration. If you use Wi-Fi devices that do not support this encryption or hotspot mode, you will have to experiment.

Pre-Srared Key - This is your Wi-Fi key (password). We recommend using lowercase and uppercase letters plus numbers or symbols of at least 8. This will eliminate the possibility of neighbors stealing traffic from you and intercepting data.

It remains to connect your laptops to the created Wi-Fi network. If you do not know how to do this, see this material: setting up wifi in windows 7

Port forwarding for torrents

As you know, in order for someone to be able to establish an incoming TCP connection with you, you need to set up port forwarding on a computer in the local network 192.168.1.0/255.255.255.0 formed by the router. So, let's turn TCP port 55555 to the local IP address of the computer with the torrent client, for example, to 192.168.1.254. Due to the fact that it is impossible to make static bindings of ip addresses to MAC in the settings of this modem, I suggest setting a static ip address manually. This is done in the properties of the same Internet protocol ( TCP/IPv4) on the local machine.Fill in the lines like this: ip address 192.168.1.254, subnet mask 255.255.255.0, gateway 192.168.1.1, dns1 192.168.1.1, dns2 8.8.8.8

We go to the admin panel of the modem in the section AdvAncedsetup/NAT/virtualserver:

Configuring forward for the TCP protocol external port 55555 per socket 192.168.1.254:55555 :

For torrents, UDP port 55555 should also be forwarded. In the mtorrent torrent client, you need to specify the forwarded port. To do this, go to Settings / Connection / "Port for incoming connections" and put 55555 there.

A set of firmware of different versions for modems Promsvyaz M200A, Promsvyaz M200B, ZTE ZXV10 W300 without 802.11N support download . For anex A modems, the firmware with the corresponding index is suitable.

See also the continuation of the article, which includes correct setting DHCP server: Configuring IPTV ZALA on the Promsvyaz m200a modem

If you failed to set up the modem or need to set up a more complex configuration, you can call a specialist at home for a fee. Customization prices. With us, setting up a Wi-Fi modem has become even easier!

The most important thing in one video:

Nowadays, wireless modems are in demand, and many users are interested in the question of how to set up Wi-Fi on a modem on their own. In fact, the principle of setting is no different from the router. But there are some differences and features that you need to know.

Entering the settings menu

First of all, to enter the modem settings menu, you need to turn on the device and connect a computer to it. It is also immediately worth noting that modem is accompanied by an instruction that specifies the username and password for entering the interface, as well as the IP address of the device.

So, we connect modem to the computer and launch any browser. In the address bar of the browser, you need to register the IP of the modem. Press "Enter".

At the next stage, the system will ask you to enter a username and password. As mentioned above, this data is contained in the instructions for the device. As a rule, the login is admin, the password is admin. Entered and click "Login" or "Login". So we got into the control system. Now you can move on to the question of how to enable Wi-Fi on the modem.

Setting up a wireless network

For settings wireless communication on the main settings page, go to the "Basic" section. After that, open the "WLAN" section. First of all, we put a tick here in the line "Enable WLAN".

There are also a few items that need to be configured:

• SSID is the name of the network that will be displayed when connecting to other computers, smartphones, tablets, and so on. You can enter any name. But remember that only letters of the English alphabet can be used.
• Maximum number of accessing device - here you can specify maximum amount concurrent connections.
• Below there is another SSID line, in front of which you need to check the box. This will put the wireless network into "Enable" mode.
• Security - in this line you can select the type of encryption. The most secure type today is WPA2PSK.
• WPA pre-shared key - here you can assign a password for your local network. It will be required to connect to Wi-Fi. You invent it yourself. As with the network name, only Latin letters and/or numbers can be used here.
• WPS - here just uncheck the box (if installed).

After entering all the necessary data, you should save the parameters. To do this, click the "Submit" button. This completes the wireless setup.

You can connect various devices equipped with a Wi-Fi adapter to it. In order to disable Wi-Fi on the modem, you will need to enter the options menu again and simply uncheck the "SSID" line.

It is worth noting that the instructions for setting up modem Huawei were described above. In other models of similar equipment, the names of some sections may differ. Although the principle of setting is always the same.

For example, to disable Wi-Fi on D-Link devices, go to the "Wi-Fi" section and select the "Wireless settings" heading (wireless network settings). After that, you just need to uncheck the box "Wireless enable".

How to set up WI-FI on a modem: Video

WAN connection setup

Above, we looked at how to distribute Wi-Fi from a modem, but we were talking about a local network. In other words, you will not have access to the Internet.

To connect to the network, you will have to set up a WAN connection, which means requesting data from the provider. That is, when you connect to the Internet, the provider issues you a contract that contains all the necessary data about the network.

Everything is extremely simple here. We return to home page in modem settings. Go to the "Basic" "WAN" section. Here we click on the line "Internet ...".

1. In the line "Connection type" you need to set the value "PPPoE".
2. UserName - here you should enter the username (login) that the provider assigned you when connecting.
3. Even lower will be the line "Password" - this is the password that the provider gave you when you connected (enter it).
4. To save the entered parameters, click the "Submit" button.

There are a lot of different ones on the market right now. wifi router s from different manufacturers. And that's good, there are plenty to choose from. But right after buying a router, we need to install, connect and configure it. And if the connection process practically does not differ depending on the model, then the setup process itself and the page with the settings of the router can be different even from one manufacturer.

It is very difficult to give detailed and step by step instructions by setting different models. But I'll try. In this article, I will describe in detail and show how to install and configure a Wi-Fi router. No matter what make and model you have. This universal instruction is suitable for both setting up a new router and reconfiguring it. You can do everything yourself. And it is not necessary to pay for the setup of specialists.

Entering the router settings. How to access the web interface?

Each router has its own web interface (site with settings, control panel), which can be accessed through a browser by going to the appropriate address.

Important! To enter the router settings and configure it, your device (PC, laptop, smartphone, tablet) must be connected to the router via a cable, or via a Wi-Fi network. In this case, access to the Internet on the computer may not be. You don't need internet to access the control panel!

If your computer has a high-speed connection (may be with the name of your provider), then after connecting through the router, you do not need to run it!

To enter the settings we need find out the address our router and factory username and password for authorization. This information is located on the body of the device itself. Looks like this:

On a computer or mobile device that is connected to the router, open a browser (Opera, Chrome, Yandex.Browser, etc.) and go to the address indicated on the case. Or try 192.168.1.1 and 192.168.0.1.

Important! The address is entered in the address bar, not in the search bar. Many people get confused, and instead of a page with settings, they end up on a page with search results of some search engine.

On the login page, you need to enter a username and password. The factory ones are indicated on the body of the device. Most often these are admin and admin. On some models, the default settings are not protected, and immediately after entering the control panel, you need to set a login and password.

Articles that may be useful to you at this stage:

If the settings page has opened, then we can continue. If not, then see the article with solutions to this problem at the link above.

How to set up a Wi-Fi router?

In order to use the Internet through a router, you need at least:

• Set up an internet connection.
• Set up a Wi-Fi network.

In most cases, this is sufficient. I also advise you to change the password that protects the web interface of the router. Is there some more IPTV settings, USB drives, parental controls etc., but not everyone needs them.

In the control panel of almost every router there is a so-called "Master quick setup", aka "Quick Setup". On some devices, it is open immediately after entering the control panel. It can be used to configure the Wi-Fi router step by step. Internet connection, wireless network, etc. For example, how it looks like TP Link:

You can try it, it's very convenient.

Internet setup. The most important step

The main thing is correctly configure the router to connect to the provider. If he can not connect to the Internet, then on all devices there will be a connection "Without access to the Internet." Many users who try to set everything up with their own hands most often encounter problems at this stage.

Each ISP uses a certain type of connection. Dynamic IP (DHCP), Static IP, PPPoE, L2TP, PPTP. This type of connection must be specified in the control panel of the router, and set certain parameters that are issued by the Internet provider.

Important! You must know exactly what type of connection your ISP has. Also all the necessary data to connect (Username: Password) if they are needed. As a rule, this information is indicated in the contract that you received when connecting to the Internet.

Some providers bind by MAC address. This is also desirable to clarify.

If your provider uses a "Dynamic IP" (DHCP) connection, then the Internet should work immediately after the connection, since this type of connection is set by default on routers.

If the Internet through the router is already working (and you didn't run any connections on the computer), then you can skip this section and go straight to setting up Wi-Fi.

When the connection type is PPPoE, L2TP, PPTP, or Static IP (which is very rare), then you need to set the necessary parameters. Usually, this is the username and password that the provider gave you. In the control panel, the section with these settings is most often called: "WAN", "Internet", "Internet".

For example, how the PPPoE connection setup on an ASUS router looks like:

Other examples:

Target: so that the Internet through the router will work on all devices. By cable and Wi-Fi. If this does not happen, then it is pointless to continue the setup.

You can always call the provider and clarify what parameters and where you need to specify. Many of them help over the phone.

Articles you might find useful:

I hope everything worked out for you.

Change Wi-Fi network settings

I highly recommend changing the Wi-Fi network name and password. It is also desirable to set your region. Everything is simple there. You can do this in the section with wireless network settings. It can be called differently: "Wi-Fi", "Wireless network", "Wireless", "Wireless mode". If you have a dual-band router, then the settings must be set separately for the network at a frequency of 2.4 GHz and 5 GHz.

• In the field "Network name" (SSID) you need to register a new name. English letters.
• In the "Password" field (wireless key) think up and write down a password. Minimum 8 characters. Protection type - WPA2 - Personal.
• Well, there should be a "Region" field. Change it to yours.
IPTV on ASUS routers.

If something goes wrong during the setup process, you can always reset the settings to the factory settings and try to set everything up again. On the case, find the "Reset" or "Reset" button, press it and hold for about 10 seconds. By the indicators, you will understand when the reset occurred.

You can leave questions in the comments. Only I have a small request, describe the problem in detail. Write the router model. And it is very difficult to understand and advise something when you do not understand the question itself. Best wishes!

Before connecting an adsl modem to a wifi router, you should make sure that the modem is correctly configured and is able to provide a stable Internet connection.

In addition, you will need a twisted-pair crossover cable. This cord is included with most .

It is short and ends at both ends with an RJ-45 plug, reminiscent of a telephone connector.

If you do not have a cable, you can easily purchase it at a computer store. Specialists often call such a cord a “patch cord”. To ensure noise immunity (which contributes to), you should choose a cable as short as possible (0.5-1 m). The price of a patch cord is 100-200 rubles.

So, to connect a wifi router via a Rostelecom adsl modem, you will need an ADSL modem directly, a Wi-Fi router and a connecting patch cord.

The setup of a classic adsl modem / wifi router by Rostelecom is described in detail in articles and.

If you have any difficulties setting up an adsl modem, you can always ask us a question in the comments to this article or using a special service.

How to connect adsl modem to wifi router?

Here we will dwell in detail on how to connect a wifi router via an adsl modem.

1. 1. Connect either end of the cord to the ADSL modem connector labeled "LAN". If there are several such connectors (LAN1, LAN2, ...), then you can use any of them. On some models given port denoted by "Ethernet" is alternative name connector for RJ-45 connector;
2. 2. Place the other plug of the patch cord into the Wi-Fi router's "WAN" jack (which may also be labeled "Internet");
3. 3. Connect the provider's Internet cable to the "DSL" connector of your modem. There are also the following designations: "ADSL", "Line". The standard ADSL modem connection diagram is shown in the figure:
   
   
4. 4. Make sure both devices are plugged in and turned on.

How to set up wifi router via adsl modem?

To configure a Wi-Fi router to connect to an ADSL modem:

You may also need to specify the provider's address and configure the MAC address of the router. Check the need to configure these parameters in the provider's support service

1. 4. Save the router settings - if the data is entered correctly, the adsl modem / wifi router Rostelecom connection should work properly. Read about the correct configuration of the local network settings on a stationary computer in the articles and, and the intricacies of connecting to WiFi mobile devices discussed in articles and.

Connecting a wifi router via a Rostelecom adsl modem: possible problems

If an error occurs when connecting the adsl modem to the wifi router, first of all you need to check the following points: