The use of modern technical innovations requires us to change some details in everyday life. For example, using a smartphone in a car will be much more convenient if you attach the device in close proximity to you on a special holder. This way, you can not only easily answer the call, but also benefit from navigation programs or other similar applications. In this article we will look at the most common mounts for a cell phone, which allow you to conveniently fix it in the car.
Some phone holders have a suction cup, which significantly expands the possibilities of installing such a stand, including on uneven surfaces. Over time, the suction cups lose a little stickiness and do not stick well, but this can always be corrected by rinsing them in warm water (the liquid will wash away all dirt and accumulated fats). This type of cell phone holder is well designed, and all buttons or ports of most gadget models will be fully accessible without being covered by elements of the device. In addition, various mount options allow you to mount your phone on the windshield or even on the dashboard, but any other convenient place in the car will be inaccessible. 
The advantages of using this particular option include ease of installation and the absence of the need to make any changes to the interior elements, while the main disadvantage of this type of phone mount is sensitivity to the peculiarities of placement. For example, if the car window is located at a strong slope, then it will be possible to attach the suction cup only in its upper part. The too long bracket is also inconvenient to use, since it swings the smartphone violently when the car is moving.
Important!When choosing a suction cup holder, pay attention to the thickness of the rubber from which it is made. In the cold season, material that is too thick will quickly lose its elasticity, and the holder will simply fall off the glass.
Clip for attaching a phone with a flexible cord
This option for placing your phone in your car will cause you a lot more problems than benefits. Despite the fact that it allows you to fix the phone almost anywhere in the vehicle without the need for glue or suction cups, such holders will create quite a lot of noise when driving, blocking the air flow coming from the deflector. Considering that the clothespin is most often attached to the heater grille, which has many thin jumpers-blinds, it is better for you not to drive over holes and potholes, as strong shaking can cause the fastener to break.
Among the advantages of using the clip is the ability to rotate the phone 360 degrees (made possible thanks to the presence of a flexible cord), but this does not make it unique. Therefore, mounting the phone on a deflector or in any other place using this method is not the best option for solving the problem of placing a smartphone in the car.
Phone holder for steering wheel
A phone mount on the steering wheel of a vehicle is a fairly simple design in which the platform for the gadget consists of two black plastic plates that fit into each other. They have a spring inside that allows you to use the holder for phones of very different widths, holding them from below and from above using silicone rollers.
You won’t have to spend a long time figuring out how to install such a phone holder in your car. Mounting on the steering wheel is done using a silicone loop, at the end of which there is a plastic pedal. By pressing it, you can remove the holder from the steering wheel.
Among the disadvantages of this type of fastener, it is worth highlighting the limited visibility of instruments on the dashboard (in particular, the speedometer indicators are poorly visible, which can easily lead to a fine for speeding), the appearance of a feeling of motion sickness in the initial stages of using the device, which occurs due to the rotation of the phone along with the steering wheel of the vehicle. In addition, if the power cord is connected to the phone, the cord often wraps around the steering wheel when turning. True, this does not always happen.
Bracket that is adjustable
Another option for devices for holding the phone while moving in a vehicle. The adjustable bracket is mounted on the ventilation grill and is suitable for smartphones with different body widths. The gadget is inserted between two limiters, one of which extends down, thereby providing the space the phone needs. The advantages of using this type of mount include the compactness of the mount itself and the ease of installing the phone, and among the disadvantages, there are all the same disadvantages as in the case of using a clip: noise, knocking and the possibility of breaking the place where the holder is installed.
There are so many phone holders for cars that you can’t immediately choose which one is best. Some of them are similar to each other, and some are radically different from their own kind. The last option is a magnetic ball made of steel and coated with a layer of treated aluminum. 3M® VHB™ bonding material is applied to the bottom of the ball base, which can provide a secure attachment to the surface of the dashboard. The bonding layer is absolutely harmless to the place where the holder is attached, so it can be removed without any problems.
The second element that is included in the design of this mount is a magnetic washer that remains on the ball base and holds the device using magnetic attraction. Thanks to it, it is possible to change the angle of inclination of the mount.
The third component is a metal plate that is glued to the phone using 3M® VHB™. It is she who is attracted to the magnetic ball and securely fixes the gadget in one position. The silicon core guarantees smooth gliding and a strong grip, thanks to which you can easily move your phone from vertical to horizontal position, while changing the angle of inclination.
If you don’t know how to attach a phone holder to a dashboard, or all the previously purchased devices did not meet your requirements, we recommend that you turn your attention to a completely new development in the field of such inventions. It is based on the capabilities of a powerful neodymium magnet. You need to install a special ring on your phone (tablet), and place the magnetic holder itself (made of metal) in the car. After this, as soon as the smartphone is near the mount, the magnet previously installed on its cover will be attracted to the holder and ensure tight contact with it. The rubber core promotes maximum contact between the two surfaces, guaranteeing comfortable rotation of the device by 360%.
Most often, this car phone holder is installed on the control panel, and its main advantage is the ease of mounting and further placement of the device. As for the disadvantages, the main one is the inability to move the stand multiple times across the dashboard (the material from which the mount is made is intended for one-time use).
Flexible phone panel
If you know well what a standard smartphone holder is, then when you see a flexible panel (mat), you will immediately understand that it is somewhat different from the usual devices. It does not need to be glued or secured to the instrument panel in any other way, because the material of manufacture (silicone) already allows it to stick to the interior trim. The stand comes with two cables: a base (with a USB connector) and a magnetic cable with micro USB and Lightning connectors.
The phone holders are installed on the mat, and a micro USB or Lightning connector coming from a magnetic cable is inserted into the smartphone itself. After this, you need to install the cable base in place.
The USB connector is connected to the charger, after which the mat is ready for use. There is an LED indicator on the base that will let you know when charging is starting. The smartphone is placed between the clamps, like on a stand. It is important that all buttons and connectors of the device remain open, and nothing interferes with its full use.
The position of the latches can be easily changed: the smartphone can be installed both horizontally (for example, for navigation) and vertically (for communicating with family and friends). You can also choose the most convenient viewing angle. This holder is a universal device, which means it is suitable for any smartphone, regardless of screen size.
Standard holders for a cell phone in a car do not always justify trust, which is why a more practical option is often universal mounts that can be converted to use another gadget within a few seconds. In this case, the phone is fixed in one of three ways:
Using magnets, which is not the best option for fixing, since the smartphone may periodically fall.
Using a cone clamp (a more reliable fastening option, just check how easy it is to get the phone out).
Using polyurethane legs that can be expanded to suit the size of a particular device. As in the previous option, problems may arise with removing the gadget. Of course, this method of attaching a smartphone is also not without its drawbacks, but at the same time it is a good alternative to non-universal holders.
A car phone mount can have a wide variety of shapes and designs, and often turns out to be a fairly simple device. This includes a mesh pocket in which the phone fits, just like in a regular trouser pocket. Such a device is often used not only to place a smartphone, but also for temporary storage of other small items (cigarettes, keys, etc.). The mesh pocket can be easily mounted on any flat surface by gluing it to it using double-sided tape.
How to secure your phone if there is no holder
If you decide not to buy a special device for fixing your phone in the car, or you still couldn’t figure out how to choose the right holder for your phone in your car, then we suggest you consider some options for fixing your phone using improvised means.
1. We use a rubber band. All that is required of you when using this method is to insert the elastic band between the “ribs” of the interior stove grille so that the phone can be placed in the two loops formed. Of course, part of the screen will be closed, but the smartphone will be securely fastened.
2. Buy a stationery clip (binder clip). Having bought a regular paper clip, you need to remove the staples from it, bend it and wrap it with thick thread. One part (clothespin) needs to be hooked onto the air duct and secured with an elastic band, and the second will be used as a fastener for the phone. The advantages of this method include the low cost of the product and ease of execution, but the disadvantage is the complexity of subsequent removal of the phone and the possibility of rough impact on the device body, since the thread does not always soften the load. You also won't be able to change the angle of the phone, and any attempts to do so may damage the air duct grille.
3. Use wire for fixation. For those who are ready to sacrifice the integrity of the panel for the sake of a good mount for their phone in the car, there is a method based on creating a wire holder. To do this you will need strong stainless steel wire and a drill. Using the prepared tool, you need to drill holes of a suitable diameter in the dashboard, after which you should bend the wire and insert it into these holes. Now all that remains is to hang the phone or tablet by the case.
Important!This mount is only suitable for tablets in a book case, but in this case the device is not always securely fastened. Moreover, it can easily block access to the radio.
Proposed for design, a phone stand for a car will be extremely useful for drivers who often use the phone. It will solve problems with finding your phone while traveling. Thanks to its simple and reliable design, work will not take much time.
Step 1. Tools.
To create a stand you will need:
1. Aluminum tube with a diameter of 47 mm "f. 4";
2. Connecting angled tubes at 45° and 90° (aluminum or copper). They are cheap and sold at any hardware store.
3. Hard wooden sticks (you can take ice cream sticks);
4. Epoxy glue or any other glue with similar qualities;
5. Phone case or case;
6. Cable ties (they will be needed to secure the case);
7. Hacksaw;
8. Ruler;
9. Knife.
Step 2. Frame assembly.
Before starting work, you should decide on the installation location of the telephone stand. It should not interfere with using the audio system, recharging, or other daily activities in the car. Only after this can you start taking measurements.
The aluminum tube needs to be cut into 3 parts. The shortest part is attached to the 45° angle tube. The horizontal part (about 5 cm) connects the 90° and 45° corner tubes “f.2.1 – 2.2”. A vertical pipe (approximately 10-13 cm) will hold the stand itself. All tube connections must be lubricated with glue so that nothing falls off during movement.
Step 3. Attaching the cover.
On the back side of the cover we make 3 pairs of cuts (the depth of the cut should correspond to the tips of the ties). The cuts are parallel to the tube, which will subsequently be attached to the cover. We thread the ties through the holes and tighten them a little (the main thing is not to overdo it). We tighten the long frame tube with ties as shown in the photo. Cut off the ends if they are too long.
Next you need to cut the wooden sticks in half, insert them between the case and the aluminum tube and coat them with glue.
In our progressive times, it is difficult to meet a person who does not have a mobile phone. Even when sending a child to first grade, parents provide him with the necessary means of communication. We use modern mobile devices not only for communication, but also for gaming applications, typing, reading, as well as watching videos and much more. Often, an owner who wants to always have a phone at hand wants to position it in a convenient way. Various expensive holders are offered in stores, but from our article you will find out what you can make from
Stationery binders
Surely those who study or work in an office will have several office clips called binders on their desktop. Next, let's look at how to make a phone stand from these devices. To create a strong holder, you can use 1, 2, 3 or even more binders. Some craftsmen assemble three-dimensional structures from many different sized clips. But such stands look bulky and are inconvenient for temporary use. It is enough to fasten two binders together and do not forget to bend one metal end of the holder slightly towards the phone located on it. Even one piece with a curved ear will be enough to support a mobile device.
You can build another structure from the same binders by placing the clamps opposite each other so that the ears point to the sides. The telephone is inserted into these ends, like into grooves. To keep the clips stable, clamp a small piece of cardboard on both sides.
We use pencils
If you don’t have any binders at hand, the question may arise: how to make a phone stand out of pencils. Before building this structure, prepare 4 erasers and 6 pencils. In fact, you need to assemble a three-dimensional geometric figure - a tetrahedron. The principle is that you need to fasten two pencils with an elastic band, and insert the third between the turns. It is recommended to use pencils with an eraser at the end to prevent slipping on the table and provide a stronger grip on the phone.
Bottle models
In the household we use a lot of cleaning products and detergents. Most of them are contained in plastic containers. It can be used as a mobile device holder. Let’s look further at how to make a phone stand out of a bottle.
The type of device will depend on the shape of the container. This could be containers for shampoo, shower gel, cleaning products and others. Take a bottle twice as long as your phone. Cut off the neck and part of the container on one side approximately to the middle. All sizes are relative - measure at your own discretion. On the opposite area of the bottle, cut a hole corresponding to the parameters of the charger. You should end up with a piece that resembles a handbag or pocket with a handle. Place the phone in the stand and connect the adapter to the network through the hole. Your mobile communication device will not lie on the floor, and there will be no risk of crushing it. You learned another way - how to make a phone stand. If desired, this holder can be painted or covered with beautiful paper or fabric.
Paper clips
The simplest and most affordable option for a stand is a regular metal clip. It must be bent into a straight line and folded as shown in the diagram. The resulting product is quite strong and stable. This design holds the mobile phone perfectly without interfering with watching videos.
Cardboard and plastic cards
How to make a phone stand out of cardboard? You will need a cardboard sheet from which you will need to cut a strip measuring 10 x 20 cm. Then you need to fold it in half along the short sections. Next, draw a figure as shown in the photo below. The fold line must remain intact. Having opened the part, you will see that you have a comfortable and stable phone stand.
If you have an unnecessary card lying around (any discount card), it will also make an excellent phone stand. It is very easy to make such a device at home. Step back 1 cm from the edge of the card and bend the piece along the short side. Fold the remaining part of the card in half in the opposite direction. You will get a zigzag shape. Place the phone on the resulting ledge. The stand is ready.
Unusual coasters made from simple things
Savvy people began to use ordinary glasses as a phone holder. They only need to be turned over with the arms up, which, in turn, need to be crossed. The mobile device is located between the frame frame and the temples that hold the phone.
How to make a phone stand from a children's construction set? In this case, everything depends on your creativity and imagination. To create such a model, you need to use a platform and several bricks of various shapes. A stand made of parts can hold the phone in both vertical and horizontal positions. The tilt of the screen can be adjusted by adding or removing additional bricks.
Another interesting detail that will help keep the phone in a vertical position is the old cassette holder. It is necessary to open it and tilt the lid back, thereby turning the box inside out. You can place your communication device in the hole that once served as a pocket for an audio cassette. The convenience of the stand is that it is quite durable and transparent, and does not interfere with the use of the phone. In addition, it can be easily washed.
As you can see, from the simplest items found in every home, you can make such a useful thing as a phone stand.
With a phone holder, you won't have to spend a lot of time looking for your mobile device. It will also be reliably protected. There is less chance that someone will drop it, step on it or spill tea, and most importantly, while driving a car, you will not be distracted. For aesthetic reasons, it can be an excellent decor for a car interior.
The simplest holder is a design for the steering wheel with silicone loops. The adjustable bracket on the panel into which the gadget is inserted is distinguished by the fact that it is compact and the phone is easy to install. Another very simple holder is a ball on a magnet.
Designer coasters are made from various materials and have different shapes - it all depends on the creativity of the artist. For example, there is a lawn on a plastic stand and a phone holder at the bottom.
The gadget holder can be made as an elegant wooden stand. For example, in the form of a tree with a hollow or improvised stumps. A neat wooden stand with randomly placed slots where a mobile phone can be inserted will look original.
A wooden stand can be very laconic and resemble a photo frame into which a smartphone is inserted. A wooden organizer on a panel can have not only a cell for a gadget, but also for pens and watches. A wooden stand in the form of a figurine supporting a phone looks original, but it needs to be firmly secured.
Sometimes phone holders make a nice souvenir when you don't have a gadget. For example, a gadget stand in the form of a rotary telephone looks original, showing the connection between times. Or look unexpectedly creative when the holder is an alarm clock into which a mobile phone is inserted.
Conceptually, the holder looks like a marble figurine holding a gadget in its hands. Even in winter, a shell stand will bring back memories of the sea. The stand can look like your favorite food, for example sushi, a hamburger or a sandwich with caviar. In such souvenirs, the wildest fantasy can turn into reality.
The highlight of the holder in a minimalist style will be the original mount. For example, on the principle of a table lamp attached to a table with a clothespin. Even an ordinary stationery binder will look original as a phone holder.
It’s worth looking at things with different eyes and making a cozy soft pillow or chair for your phone. If a woman is driving, it could be a fluffy basket, an original fabric pocket, a soft envelope with a cute hinged loop. Knitted animals in the form of a stand will always help you maintain a good mood. Stylish bright accessories will not only serve you by performing certain functions, but will also help you think positively.
The holders may have a flexible cord for fastening, a suction cup, or an adjustable bracket.
When choosing a phone stand, everyone is guided by their own taste preferences. In terms of functionality, the holder must have a good fit to keep the phone safe.
How to make it yourself
From the paper clip
You can make a device that supports your phone yourself. This stand will definitely be exclusive.
Homemade holders can be of three types:
- spoiling the interior;
- not durable;
- representing a whole work of art that requires real skill.
We take the binder, remove the staples, bend them so that a holder is formed, wrap them with thread and place them in their original place, securing them with an ordinary rubber band. All that remains is to attach a simple device to the air duct. The phone is attached securely. The only negative is that the phone cannot be quickly removed from the holder.
From wire
In order to attach a phone to a wire holder, you will have to sacrifice the integrity of the front panel of the cabin, since holes will need to be drilled on it. The holder is made from strong wire, bending it accordingly and inserting it into the holes. The phone must be firmly attached to the holder.
Aluminum stand
It takes a little effort to make a stand out of aluminum. In any hardware store you can inexpensively purchase connecting tubes with angles of 45 and 90 degrees, as well as an aluminum pipe with a diameter of 47 mm. You will also need ice cream sticks and an old phone case.
You can start creating the holder after you have determined the place where it will be located. Now the necessary measurements are made. The pipe is cut into three parts. The short part is attached to a 45 degree angle tube. The horizontal part is held in 45 and 90 degree angle tubes. The longest part - a vertical pipe, 10 - 13 cm long, will hold the stand.
For greater strength, all fasteners are first lubricated with glue. A couple of cuts should be made in the case into which the ties are inserted. The cuts are on the tube. A long pipe is tied together with ties. Wooden sticks are glued between the aluminum pipe and the cover. The final stage is attaching the connecting tube to the car.
