We are pleased to present a grand new product for 2015 - Joeytech eVic VTC mini

Joyetech was able to do the impossible - release, perhaps, the best box mod. The eVic VTC mini embodies all the technological innovations and all the wishes that the vaper community expressed to mod manufacturers.

Such a successful mod deserves a detailed description.

Let's start with the body.

Joyetech did not skimp on quality; the eVic VTC mini is made in a compact case cut from a single piece of aluminum - no screws, no gaps. The build quality is impeccable, nothing rattles if you shake the mod, the buttons are pressed softly and moderately freely, with a noticeable but almost silent click. The activation button is large, spherical, located in a small recess and can be easily found with your finger. The control buttons are located in a recess that protects against accidental pressing. The mod's smooth corners ensure a comfortable hold in the hand, and the matte finish is resistant to scratches, abrasion and is pleasant to the touch. Every detail has been thought out for ease of use, for example, a very convenient lid. It is attached to two large magnets of different polarities, so it cannot be placed upside down - the lid will be pushed away. After installation, the cover remains secure and motionless.
The eVic VTC's USB charging connector is located on the front panel, which distinguishes it from many mods with a bottom charging location that cannot be placed on a table with a cable connected. When the eVic VTC mini is charging, the cable does not interfere with either placing it on the table or taking it with your usual grip to vape without interrupting the charging process.
However, to appreciate the quality and convenience of the eVic VTC case and controls, we recommend just coming to one of the Zenmod stores and experiencing the box mod in action in person!

The heart of any electronic mod is the circuit board. Joyetech eVic VTC mini owes its success, first of all, to an extremely successful board, which is far ahead of its competitors both in terms of work quality and range of capabilities, some of which most more expensive mods cannot boast of.
The board is accurate, fast, and powerful. Thermal control works flawlessly and correctly - it is the temperature, not the power, that is regulated first of all. Both nickel and safer and easier-to-use titanium and stainless steel are supported, for which Joyetech has created separate operating modes.
The mechanical mod mode is interesting - in it, the power of the eVic VTC mini is limited only by the capabilities of the battery. You can easily vape a powerful 80-100W drip (the manufacturer does not recommend using a resistance of less than 0.1 Ohm so as not to overload the output circuits), and the screen will show the actual battery voltage under load, current strength, and atomizer resistance.
The regular wattage mode is also implemented as honestly and correctly as possible. All variwatts can be divided into three categories according to their behavior when the installed power exceeds the capacity of the battery (for example, when it is too discharged): some simply turn off or show a message on the screen indicating insufficient battery power, others continue to show the initially set value, but only produce so much , as much as the battery allows, deceiving the user. And only third, honest mods, which include eVic VTC mini, show on the screen in real time the power they produce. If the user has specified a power that the battery can no longer provide, the maximum possible will be provided, and it is this that will be reflected on the screen.

Thermal control works correctly - the resistance can be fixed when the evaporator is cold, and eVic VTC will not “forget” the atomizer parameters even when changing the battery or mode. Interestingly, for the nickel, titanium and steel modes, the resistance is fixed independently.
To prevent the bright light of the screen from disturbing you in the dark, Stealth mode is provided. In this mode, the eVic VTC mini screen does not light up when in use.
Joyetech's responsible attitude towards its products is also reflected in the fact that firmware updates are provided for eVic VTC. One of the latest ones added useful features, such as real-time current display.
The bottom line of the screen can be customized to your liking - display the battery charge indicator, the number of puffs, the operating time of the mod or the current strength.

To sum up, Joyetech eVic VTC can easily be called the best box mod of the most popular 1x18650 format and can be recommended to both beginners and experienced vapers of all categories.

Brief list of features:

Vertical-oriented four-line OLED display

Replaceable 18650 battery (not included)

Spring loaded stainless steel connector

Cover held by two oppositely polarized neodymium magnets

Power range: 1 to 75 Watts (up to 120 Watts in Bypass mode)

Voltage range: 0.5 to 9 Volts

Supports resistance from 0.1 Ohm and from 0.05 Ohm in thermal control mode

Thermal control mode on nickel, titanium and stainless steel

Mechanical mode (Bypass) up to 120W

Possibility of software update

Charge from USB, can be used while charging (Pass-Through function)

Short circuit protection, overheat protection, etc.

Power setting lock function

Stealth function for vaping without activating the screen

Dimensions: 22.2 x 38.2 x 82.0 mm

Attention! This product is original (not a clone).

The eVic VTC Mini Battery Pack from JoyeTech is an upgraded version of the eVic VT Battery Pack,
which has collected a lot of positive reviews from both beginner steamers,
and from experienced ones.

In the new version, the manufacturer paid attention to all the comments on the previous model.

Differences from the first version:

A completely new design, the manufacturer has carried out a major restyling of the body, simultaneously changing the principle of painting and abandoning chrome plating;

Reduced weight and overall dimensions of the battery pack;

510 connector moved to the other side;
- support for a standard 18650 battery with the ability to quickly replace it without a screwdriver instead of a built-in non-replaceable battery;

Added the usual + and - buttons to adjust settings;

The range of power adjustment in temperature control mode has been expanded,
lower limit is now 1 W (was minimum 30 W in eVic VT);

Added a new Bypass mode, allowing the battery pack to operate in mechanical mod mode;

Structural improvements to the electronic board;

The micro-USB connector has been moved from the top side of the battery pack to the bottom and is located under the + and - buttons;

Added the ability to independently update the firmware by the user.

Key features of eVic VTC Mini:

• The manufacturer positions the battery pack
  as a universal device for all categories of users.
  For this purpose, there are three main modes of operation of the battery pack:
• Power (VW), classic wattage mode with the ability to “lower”,
  when the power supplied to the evaporator is less than the power,
  which the battery is currently delivering.
  In this mode, the user can adjust the power from 1 W to 75 W in 0.1 W increments.
  The atomizer resistance should be in the range from 0.1 Ohm to 3.5 Ohm;
• Bypass, a new mode that makes it possible to use the battery pack as a mechanical mod,
  which can handle windings as low as 0.1 ohm while maintaining all the key benefits of electronic board and protection.
  The display of the battery pack in this mode shows the current winding resistance,
  actual voltage under load and remaining battery charge.
  In this mode, you can work with sub-Ohm windings, which require a power of over 60 W to drive;
• VT-Ni & VT-Ti, temperature control modes for the state of the coil,
  designed for spirals made of nickel (VT-Ni) and titanium (VT-Ti) wires, respectively.
  The operating principle of temperature control is based on the fact that nickel and titanium change their resistance when heated.
  The electronics of the battery pack allows you to record the “cold” resistance of the coil without load and during operation,
  Comparing the initial value of the spiral and the working value, calculates its temperature.
  When the set temperature limit is reached, the electronics limits the supplied power, which maintains the set temperature level.
  The temperature limit in this mode is set from 100 C to 315 C in 5 C steps and from 200 F to 600 F in 10 F steps.
  The power varies from 1 W to 75 W in 0.1 W increments.
  Winders and evaporators with resistance from 0.05 Ohm to 1 Ohm are supported;
• Updated design in all body details. The buttons are made in black,
  made of high quality plastic and located in special recesses on the body,
  protecting against accidental pressing during transportation.
  The battery pack body is made of metal,
  The coating is made by anodizing; the user can choose from five body color options.
  All color options are matte, now the battery pack does not collect fingerprints;
• Large OLED display reflects all the necessary information during operation
  (depending on the mode and settings of the battery pack): operating mode (Bypass, VW, VT-Ti, VT-Ni),
  set temperature limit, set power for supply to the evaporator,
  vaporizer resistance, battery charge level, number of puffs taken or vaping time.
  The information on the display is located vertically;
• The ability to independently update software via micro-USB allows you to stay on the cutting edge of technology,
  since developers are constantly improving the software
  and in the future they will expand the functionality and stability of the battery pack;
• The functionality of the battery pack is ensured by 18650 standard batteries.
  To operate at maximum power, the manufacturer recommends using batteries with an output current of 20A or higher (batteries with an output current of 30A are recommended).
  The battery compartment cover is secured with four neodymium magnets for quick battery replacement.
  holding the cover firmly in place during operation.
  Also, the battery installed in the battery pack can be charged using a micro-USB port from a computer,
  or from the charger. Charging time is about 3 hours.
  It is possible to use the battery pack while charging (passthrough function);
• The battery pack board contains all currently relevant protection options: from overdischarging and overcharging the battery,
  short circuit of the evaporator or too low resistance on the evaporator,
  protection against overheating of the electronic board, limiting the duration of the puff to 10 seconds,
  and also as protection against accidental pressing of buttons
  When transporting the battery pack, a locking mode is provided for the installed power
  (turned on by pressing the + and - buttons simultaneously for 2 seconds);
• The battery pack connector is made according to the 510 standard,
  The manufacturer selected stainless steel as the manufacturing material.
  The positive pin of the battery pack is spring-loaded,
  to ensure maximum compatibility with all currently existing evaporator models;
• Universal battery pack from market veterans,
  made of high-quality materials with a huge number of useful improvements relative to the first version;

Main characteristics of eVic VTC Mini:

• Battery: 18650, with flat positive contact, output current from 20A (purchased separately);
• Voltage supplied to the evaporator: 0.5 V - 9 V;
• Adjustable output power from 1 W to 75 W in 0.1 W increments;
• Operating resistance range: from 0.1 Ohm to 3.5 Ohm (in variable watt mode), from 0.05 Ohm to 1 Ohm (in thermal control mode);
• Connector: 510, steel, spring-loaded center pin;
• Button lock: press the Fire button five times;
• Cut-off: 10 seconds (maximum puff duration);
• Dimensions: 22.2mm * 38.2mm * 82mm;
• Weight: ~120 g (without battery);
• Manufacturer: JoyeTech;

Equipment:

• 1 eVic VTC Mini battery pack;
• 1 instruction manual in Russian;
• 1 micro-USB cable;
• 1 gift box.

up

The new eVic VTC Mini TRON-S TC from Joyetech is a starter kit based on the eVic VTC Mini TC 60W mod, beloved by vapers. Or rather, its improved 75-Watt version, capable of providing temperature control not only on nickel and titanium, but also on stainless steel. For the sake of fairness, it is worth noting that only the firmware has been updated, and any vaper can turn his eVic VTC Mini 60W mod into 75W by downloading the utility from the manufacturer’s website. The highlight of the set is the new clearomizer added to the set - TRON-S.

Features of eVic VTC Mini TRON-S TC

up

The eVic VTC Mini 75W mod has all the same advantages as the eVic VTC Mini 60W: compact size, sufficient power, replaceable battery, temperature control on nickel, titanium and stainless steel. By default, all eVic VTC Mini 75W are already firmware with version 2.0, which still retains the old interface, which seems more informative to vapers, but now supports TC on stainless steel.

Thanks to the stylish design of the TRON-S clearomizer, the eVic VTC Mini 75W kit looks like a new device. The vaper has six colors to choose from: gray, black, white, red, mint and gold. The body is made of steel. Thanks to its dimensions of 82x38.5x22 (138.6x38.5x22 with clearomizer) mm, the mod easily fits into the palm of your hand and allows you to hover unnoticed.

Functionality

up

Variwatt

The eVic VTC Mini 75W has a variable watt that can be adjusted from 1 to 75 Watts in 0.1 Watt increments.

Temperature control

The eVic VTC Mini 75W mod supports temperature control on nickel, titanium and stainless steel out of the box. The adjustment range is 200–600 °F or 100–315 °C, in increments of 10 degrees for Fahrenheit and 5 degrees for Celsius. In TK mode it is possible to adjust the power over the entire wattage range - from 1 to 75 Watts. If desired, the resistance can be blocked manually. There is no Joule adjustment in the mod, but it may appear in future firmware.

Sabom

eVic VTC Mini 75W has full support for subwoofer in all modes: in variwatt you can use windings with a resistance from 0.15 to 3.5 Ohm, in TK - from 0.05 to 1 Ohm (up to 1.5 Ohm with firmware version 3 ), in mechanical mode - from 0.1 to 3.5 Ohms.

Mechmod

The mod allows you to turn yourself into a “safe mech mod” by turning on the appropriate mode. The voltage from the battery begins to supply in full, but the board’s protections continue to work.

Battery

The eVic VTC Mini 75W has a removable battery, the battery compartment is implemented using magnetic cover technology. The battery format is 18650. The manufacturer recommends using batteries with a current output of 20 Amps. There is a USB port on the front of the mod that is used for charging. Its location allows you to place the device on the table while charging, as well as use the mod, since the e-cigarette has a paste function. The battery can be charged either via USB (maximum current 1 Ampere) or in a separate device. The positive contact of the battery compartment is spring-loaded.

Display

The display of the eVic VTC Mini 75W mod is made using OLED technology, which gives it the ability to display information equally well both in the dark and in direct sunlight. Screen diagonal 0.96 inches. In firmware version 2.0 (installed by default), the mod displays data on resistance, power, temperature and voltage, and also shows the remaining battery capacity. This is the “old” interface that is retained in some amateur firmware.

In version 3.0, the screen has already been updated, showing information differently, in a more structured way. In the future, it will also be possible to display Joules with the corresponding functionality.

The display has a stealth mode, in which the screen does not light up while vaping, but starts working when the vaper changes the settings. The device also has a partial locking function, during which the mod responds to pressing any buttons with “Key Lock” and prevents accidental activation or changing settings.

Connector

To mount the clearomizer in the eVic VTC Mini 75W, a spring-loaded steel pin of 510 format is used.

Protection

The Joyetech mod is protected from all possible misfortunes:

• from short circuit;
• from overheating;
• from deep discharge;
• from overcharging;
• from low resistance;
• from damage to the evaporator - cut-off 10 seconds.

The device does not have ventilation holes.

Firmware

The eVic VTC Mini 75W mod allows you to easily update your firmware. All you need is a computer, a USB cable and the Internet to download new firmware. After downloading the application and the firmware itself, for example, from the manufacturer’s website, you should connect the device to the computer, launch the software and wait for the end of the process, which takes literally a few seconds. By default, eVic VTC Mini 75W has firmware version 2.0, which adds stainless steel thermal control and increases the power of the device. Firmware 3.0 provides the following features:

• New TCR mode. Allows you to “train” the mod to work with spirals that are not officially supported by the device. For example, with stainless steel SS 304, SS 316, SS 317. Detailed instructions can be found on the firmware page
• In temperature control mode, the resistance range has been expanded: 0.05–1.5 Ohm instead of 0.05–1 Ohm
• Watt adjustment is faster
• Interface update

Clearomizer

up

The eVic VTC Mini TRON-S TC kit uses the stylish TRON-S clearomizer. This clear comes in the same colors as the mod, so it fits perfectly with the eVic VTC Mini. Additionally, Joyetech produces silicone rings in four colors so that vapers can decorate their TRON-S with them. A clearomizer is created from steel and Pyrex glass. Compared to the eGo Mega One, the “window” for monitoring the liquid level is much wider.

The clear is partially dismountable: the lower base is unscrewed, the mouthpiece is attached to the 510 connector. Bottom filling. The draft adjustment is hidden, that is, there are no holes on the airflow ring that spoil the appearance of the clearomizer. Any evaporators from eGo Mega One are suitable for the clear, but it is impossible to create your own windings. The volume of the “tank” is 4 ml. Clearomizer connector - 510.

Control

up

In terms of control, eVic VTC Mini 75W is similar to other mods from Joyetech. There are only three control buttons: main, “+” and “-”. To lock and unlock the mod, press the hover button five times quickly. To access the menu, this button must be pressed three times. In the menu, you can select the desired line “-” and perform an additional action for the mode with the “+” button. The menu gives access to five modes: temperature control on nickel, TC on titanium, TC on stainless steel, mechanical mod and variable watt. Using the “+” button, you can select one of them, and then, while vaping in this mode, set the temperature or power using “+” and “-”. To switch Fahrenheit to Celsius and vice versa, you need to “scroll” the temperature outside the range.

For partial blocking, press “+” and “-”. Stealth mode is activated by holding down the minus sign and the main button. To block the resistance of the atomizer, you need to go to the menu and select the line with resistance with the minus sign, then confirm the decision with the right one. Power in TC mode is set from the menu. To do this, you need to select the TC mode in the menu using the “-” button, and then proceed to direct adjustment using “+”. The power only increases, and if you “overshoot” the required value, you will have to “go to the second round”. In firmware version 3.0, you can choose what the screen will display: puff time, number of puffs, or current. To do this, you need to press “-” three times in the menu and select the desired mode.

Options

up

• dimensions - 82x38.5x22 mm;
• dimensions with clear - 138.6x38.5x22 mm;
• weight without battery - 119 grams;
• weight with battery - 163 grams.
• clearomizer volume - 4 ml.

Characteristics

up

• power - 1–75 Watt;
• temperature - 200–600 °F; 100–315 °C;
• resistance in TC mode - 0.05–1 Ohm; (0.05–1.5 Ohm on firmware version 3);
• resistance in mechanical mode - 0.1–3.5 Ohm;
• resistance in variable watt mode - 0.15–3.5 Ohm;
• battery type - 18650;
• maximum charging current - 1 Ampere;
• connector - 510, spring-loaded;

Equipment

up

The eVic VTC Mini TRON-S TC set is available in “full” and “without charging (no wall adapter)” configurations. As the name implies, the second differs only in the absence of a network adapter. The rest of the set includes:

• the mod itself;
• clearomizer TRON-S 4 ml with pre-installed 0.1 Ohm evaporator;
• spare nickel evaporator 0.2 Ohm;
• spare titanium evaporator 0.4 Ohm;
• USB cord;
• instructions;
• gift wrap.

Boxmod eVIC VTC MINI 75W is a logical continuation of the successful eVIC line. Joytech technology is advancing by leaps and bounds and now the userreceives a three-mode device in one box + the ability to hot-swap batteries without opening the case.

eVIC VTC Mini 75W - a balanced device with an LED screen and controls is actually a microcomputer with three operating modes:

- VW mode. A simple and familiar varivolt mode with the ability to adjust power/voltage up to 75W. As a rule, 75 Watts are needed by out-and-out fanatics, as it allows you to heat any “heavy” coils with any diameter to red hot. Normal, quiet vaping mode up to 25W.

- Bypass modeor bypass. This mode was also provided for fans of mechanical mods. The peculiarity of the mode is that, as in mechanical modifications without electronic filling, the battery power is directly transferred to the evaporator and is not limited by anything. In this mode, the manufacturer requires the coil resistance to be in the range of 0.1-3.5 ohms.

- VT modeor temperature control. Actually, it is for this mode that similar models of electronic cigarettes are bought. Thanks to modern electronics and the right evaporators based on titanium (VT-Ti) or nickel (VT-Ni), the user has the opportunity to change the temperature of the coil itself in steps of up to 5C degrees! Now the vaper (smoker) will never complain about overheating of the coil or the discomfort of a burned throat. An additional advantage of “temperature control” is the gentle treatment of steam generators and cotton, which is now designed to last much longer until the next replacement! Evaporator operating temperature from 100 to 315 degrees Celsius)

I would also like to draw your attention to the ease of changing the 18650 battery. You just need to remove the cover and change the power supply. The lid is attached with neodymium magnets and fits into the case like a glove. And also the ability to change firmware as needed. All our models are always firmware with the latest version provided by the manufacturer Joytech.

Characteristics:

Manufacturer: Joyetech.
Connector: 510.
Operating modes: VT-Ti / VT-Ni / VW / Bypass (mechanical mod mode)
Output power: 1 - 75 W.
Battery Type: 1 x 18650 (Replaceable)
Range of supported resistance VT: 0.05 - 1.0 Ohm.
Supported VW resistance range: 0.1 - 3.5 Ohm.
Operating temperature range: 100-315℃/200-600°F.
Material: stainless steel, aluminum.
Size: 22.20 x 38.20 x 82.00 mm

Equipment:

Box mod eVic VTC Mini - 1 piece (without battery)
USB cable - 1 pc.
Instructions.

Lifehacks of eVic VTC Mini for every day:

1. Lock the main button by pressing it five times. This will prevent you from accidentally turning on the device in your bag or pocket.

2. Is the always-on screen annoying? Press and hold the main button and the left adjustment button. it will be written on the screenstealth on. Soar and don't waste extra energy
3. If you press and hold the two small adjustment buttons, the mode will turn onkey lock. This will protect you from accidentally changing your favorite settings without blocking the main button!
4. If you changed the steam generator while smoking, the smart eVIC VTC will display on the screennew coil right, same coil left - and will prompt you to select the right button if the steam generator is new, the left button - if you are sure that you have not changed anything!

Firmware 2.0

In November, an official new version of the interface was released foreVIC VTC Mini- version 2.0 . Now the vaper can read from the screen and control various information without switching through the menu. At the same time, on the device’s display you can monitor the current power (power), always see the current resistance of the spiral (Ω), the current strength of the current when the button is pressed (A), Voltage (V), and also as a pleasant bonus you can read the number of breaths and the total device operating time. By the way, this allows you to understand whether the device was sent new and warns against unscrupulous sellers.

In addition, in the new version of the interface foreVIC VTC Mininow it is possible not only to work withtitanium And nickelspirals in temperature mode, and a new mode has appeared for temperature control - for wire made ofstainless steel(stainless steel coil)

All our devices are already firmware so that the user immediately receives the new 2.0 interface.

Firmware 3.0

On December 21, Joytek provided the next firmware version 3. Now the device can work with coils of various brands: nickel, titanium, stainless steel, NiFe. The interface has also changed to the current version. All our devices are already firmware so that the user immediately receives the new 3.0 interface.

This VT software is for upgrading your eVic-VTC Mini to the latest Firmware. Your temperature control device will always be up to date because of upgradeable firmware.

What's new in Version 3.05?
Adjustable Timeout Duration
For safety concerns, if you hold the fire button over a certain time, the device will shut down automatically. Press the fire button 5 times to turn it on again.
Due to different vaping habits, you’re allowed to set the timeout duration from 5 to 15 seconds as you prefer. Hold the fire button and “+” button simultaneous to active the menu. Press the “+” button 2 times to shift to timeout set interface. Press the “－” button to set the timeout duration. Press the fire button to confirm.

Check Preheat Status With Ease
We made it easier to check the preheat status. When the preheat function is on, the wattage icon will be turned reversed to indicate that your preheat is now on. The “W” icon will turn back to normal when you turn the preheat function off.

Previous updates
Preheat Function Available
We listened to our fans about adding the preheat into our existing firmware upgradeable devices. And now, the preheat function is available. This is especially an essential when using an RDA, RTA, ceramic heads and so on.

Simply long press the fire button and “+” regulate button simultaneously to enter into the regulation interface. Then press the “+” button 2 times to enter into Preheat Setting Menu 1. Press the fire button to switch between preheat power and preheat duration. Press “+” or “-” buttons to regulate. Long press the fire button to confirm.
1: When you enter into the preheat menu, press the “-” button first then to regulate the preheat power and duration.

Simplified New Interface
We redesigned the user interface based on the creatives by our fans. It is simple and clear with all the essential elements on display.

Game Mode
We added the new Game Mode on Version 3.03 in order to bring more fun to you.
Simply press the fire button and right regulatory button simultaneously to enter into the menu regulation interface 1 . Then press the right regulatory button again to enter into the Game Mode menu 2 directly. Choose Easy, Normal or Hard level and press the fire button to start the game. Press the fire button and right regulatory button simultaneously to exit.


Custom Logo
Users can upload custom logos onto your eVic-VTC Mini. The logo should be single color bmp. picture with limited 64*40 pixel.

How to achieve?
1. Download the new VT Software 1.20 and upgrade your eVic-VTC Mini to firmware V3.02 or higher version first.
2. Upload the logo you prepared.
3. Press the fire button and right regulatory button simultaneously to enter into the on/off menu of custom logo function. Then you're ready to enjoy it.


Modes Shift Adjustment
On the new firmware V3.02, we made a slight change to the modes shifting. In the main menu, we’re now having TEMP, TCR, POWER, BYPASS and START modes.
We integrate normal VT modes (Temp Ni, Temp Ti, Temp SS316) into the TEMP sub-menu. When you at the sub-menu, just press the Up button to switch among Temp NI, Temp TI, and Temp SS316 modes.
We also changed the display of TCR mode, that is to say, we added the actual TCR value onto the mode display (e.g. TCR 120 M1).

START Mode
We added START Mode for those who are new to the CUBIS and BF heads. You can easily get started. The BF SS-316 and BF Clapton series heads can be applied under this mode. Based on it’s resistance, there will be an recommended output range with the dash line marking the maximum. You can get the best vaping experience when using in this recommended range. Still you can adjust the wattage beyond the range as to your preference.

Note: 1. The Start Mode will automatically save ten groups of output settings. Each resistance contains an output power setting. It can be adjusted and will be saved once you change the output wattage.
Note: 2. When ten groups of profiles are saved, the first profile will be deleted if a new resistance is added. And it is the same to continue.
Note: 3. On the display, the dash line with the word BF represents the recommended maximum output wattage for current BF atomizer head.

New Interface
Compatible with eVic-VTC Mini, the software to upgrade firmware to 2.0 Version is now available. The 3.0 Version, presents overall information in a more clear, precise and elegant way.

It is newly added with SS316 mode which especially goes with BF SS316 head.
At the same time, in VT mode, the resistance range has upgraded to 0.05-1.5ohm.